Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
- 3. General data
   - 3.1. Cars with petrol engines
      3.1.1. Masses and transfer numbers
      3.1.2. Operational liquids
      - 3.1.3. Changes in a car design from 1984 to 1986.
         3.1.3.1. Engine
         3.1.3.2. Head of the block of cylinders
         3.1.3.3. Block of cylinders of the engine
         3.1.3.4. Krivoshipno-shatunny mechanism
         3.1.3.5. Cranked shaft
         3.1.3.6. Gazoraspredeleniye system
         3.1.3.7. Engine mount
         3.1.3.8. Cooling system
         - 3.1.3.9. Carburetor
            3.1.3.9.1. The Ford carburetor with we change section of a diffuzor
            3.1.3.9.2. Weber carburetors
            3.1.3.9.3. Pierburg carburetor
         3.1.3.10. System of injection of fuel
         3.1.3.11. Ignition system
         3.1.3.12. Coupling
         3.1.3.13. Mechanical four-speed transmission
         3.1.3.14. Mechanical five-speed transmission
         + 3.1.3.15. Automatic transmission of Ford A 4 LD
         3.1.3.16. Power shaft and back bridge
         3.1.3.17. Steering system with the hydraulic booster
         3.1.3.18. Forward suspension bracket
         3.1.3.19. Back suspension bracket
         3.1.3.20. Brake system
         + 3.1.3.21. Electric equipment
         3.1.3.22. General data
      + 3.1.4. Changes in a car design from 1987 to 1989.
      + 3.1.5. Changes in a car design with 1990 till February, 1993.
   + 3.2. Cars with diesel engines
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






3.1.3.9. Carburetor

3.1.3.9.1. The Ford carburetor with we change section of a diffuzor

GENERAL INFORMATION

NEEDLE VALVE

Since May, 1983 (a code of date of manufacturing of "DL") the new type of the needle valve operating supply of fuel to the poplavkovy chamber, and also a new clip of the needle valve is entered.

In case of repeating stops of the engine directly after its start it is necessary to uncover the carburetor and if in the poplavkovy chamber there is no fuel it is necessary to arrive as follows.

PERFORMANCE ORDER
1. To take an axis of a float and a clip of the needle valve (if was present at this type), paying attention, that both these an element did not fall in the poplavkovy chamber.
2. To take the needle valve (is not subject to repeated installation).

Prevention

It is impossible to unscrew bolts of fastening of the elements which are dosing out fuel, with a view of simplification of access to a float.


3. To establish the new needle valve and a new clip, paying attention to the correct placement of a clip in the flute of the valve provided for it.
4. To insert a float, paying attention to the correct provision of remote laying between the holder of the lever and the needle valve, and to insert an axis into cut of the holder of a float.
5. Several times to move a float, checking possibility of its free rotation on an axis.
6. To establish new laying of a cover of the poplavkovy chamber and to tighten bolts of fastening of a cover of the carburetor the moment of 2,5 Nanometers.

Prevention

Carburetors with changeable section of a mouth in an initial stage of manufacturing were not equipped with a clip of fastening of the needle valve.


MANAGEMENT OF THE BUTTERFLY VALVE

Lever of a butterfly valve of the Ford carburetor

And – the lever of a butterfly valve,

In – a core from an artificial material

Since January, 1985 (a code of date of manufacturing of "FJ") the lever (And) a butterfly valve, a core (In) from an artificial material is changed. At violation of operability of the mechanism of management by a butterfly valve of the old type caused by wear of a core (In) from an artificial material, it is necessary to establish the lever and a core of new type.


Prevention

There are two types of levers of a butterfly valve of a mix – with cut for a core direct or bent. It is necessary to use surely the lever with cut of the same form, as well as in a factory complete set.