Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
- 3. General data
   - 3.1. Cars with petrol engines
      3.1.1. Masses and transfer numbers
      3.1.2. Operational liquids
      - 3.1.3. Changes in a car design from 1984 to 1986.
         3.1.3.1. Engine
         3.1.3.2. Head of the block of cylinders
         3.1.3.3. Block of cylinders of the engine
         3.1.3.4. Krivoshipno-shatunny mechanism
         3.1.3.5. Cranked shaft
         3.1.3.6. Gazoraspredeleniye system
         3.1.3.7. Engine mount
         3.1.3.8. Cooling system
         + 3.1.3.9. Carburetor
         3.1.3.10. System of injection of fuel
         3.1.3.11. Ignition system
         3.1.3.12. Coupling
         3.1.3.13. Mechanical four-speed transmission
         3.1.3.14. Mechanical five-speed transmission
         + 3.1.3.15. Automatic transmission of Ford A 4 LD
         3.1.3.16. Power shaft and back bridge
         3.1.3.17. Steering system with the hydraulic booster
         3.1.3.18. Forward suspension bracket
         3.1.3.19. Back suspension bracket
         3.1.3.20. Brake system
         + 3.1.3.21. Electric equipment
         3.1.3.22. General data
      + 3.1.4. Changes in a car design from 1987 to 1989.
      + 3.1.5. Changes in a car design with 1990 till February, 1993.
   + 3.2. Cars with diesel engines
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






3.1.3.7. Engine mount

GENERAL INFORMATION

Identification of new type of a pillow of an engine mount

And – a nut of fastening of a pillow to an arm of an engine mount,

In – bolts of fastening of a pillow to an engine mount arm

Since February, 1983 (a code of date of manufacturing of "DK") metallo-rubber pillows of an engine mount are entered.

In case of emergence in a body of the fluctuations which are showing in the course of start of the engine and its work idling in cars, made till February, 1983, it is necessary to arrive as follows.

PERFORMANCE ORDER
1. To check, whether makes number of turns of the engine idling 800±25 rpm.
2. If nevertheless at the correct size of number of turns of the engine idling fluctuations are transferred in a body, it is necessary to replace metallo-rubber pillows of an engine mount.
3. To remove the top part of a casing of a radiator.
4. To unscrew a nut (And) pillow fastenings to an engine mount arm.
5. To suspend the engine by means of a waist and to unscrew bolts of fastening of a pillow to an engine mount cross-piece.
6. To remove laying of round section or the clamps established on bolts of a new metallo-rubber pillow of an engine mount.
7. To establish a metallo-rubber pillow of new type and to tighten bolts of its fastening to an engine mount cross-piece the moment of 50-60 Nanometers.
8. To lower the engine and to tighten a nut of fastening of a pillow to an engine mount arm.

Prevention

To check, whether there is basic laying of big diameter on the place.


9. To establish the top casing of a radiator.