Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
- 3. General data
   - 3.1. Cars with petrol engines
      3.1.1. Masses and transfer numbers
      3.1.2. Operational liquids
      + 3.1.3. Changes in a car design from 1984 to 1986.
      - 3.1.4. Changes in a car design from 1987 to 1989.
         3.1.4.1. OHC engine
         + 3.1.4.2. Dm3 CVH 1,8 engine
         + 3.1.4.3. DOHC engine
         - 3.1.4.4. Service and repair
            3.1.4.4.1. Ignition system
            3.1.4.4.2. Injection system
            3.1.4.4.3. Scheme of EES IV system of the DOHC 2,0 engine of dm3
            3.1.4.4.4. Check and EES IV system adjustment
            3.1.4.4.5. Elimination of malfunctions
            3.1.4.4.6. Check of elements of EES IV system
            3.1.4.4.7. Gazoraspredeleniye system
            3.1.4.4.8. Head of the block of cylinders of the engine
            3.1.4.4.9. Engine dismantling
            3.1.4.4.10. Engine assembly
            3.1.4.4.11. Greasing system
         + 3.1.4.5. Coupling
         3.1.4.6. Mechanical five-speed transmission of type N
         + 3.1.4.7. Mechanical five-speed transmission of MT 75 type
         3.1.4.8. Automatic transmission
         3.1.4.9. Forward suspension bracket
         + 3.1.4.10. Brake system
         + 3.1.4.11. Electric equipment
         3.1.4.12. General data
      + 3.1.5. Changes in a car design with 1990 till February, 1993.
   + 3.2. Cars with diesel engines
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






3.1.4.4.11. Greasing system

GENERAL INFORMATION

System of greasing of the DOHC engine

1–case of the oil pump,
2–the driveshaft of the oil pump with a rotor,
3–cover of the oil pump,
4–asterisk of the oil pump,
5–Perepuskny valve,
6–oil filter,
7–laying,
8–sensor of pressure of oil,
9–index of level of oil,
10-directing the index of level of oil,
11-the pipeline of supply of oil with a maslopriyemnik,
12-partition of the oil pallet (oil deflector),
13-laying of the oil pallet,
14-oil pallet,
15-stopper oil plum

Check of pressure of oil

PERFORMANCE ORDER
1. To warm up the engine to normal working temperature.
2. To unscrew the sensor of pressure of oil.
3. To screw up on its place the manometer union.
4. To start the engine and to check pressure of oil idling and at 2000 rpm. To compare the received sizes to demanded values (see section 3.1.4.3.1.5).
5. To disconnect a manometer.
6. To screw up the sensor of pressure of oil.

Unscrewing of a bolt of the tension device kardanny chains of the oil pump of the DOHC engine

 

Removal of the oil pump

PERFORMANCE ORDER
1. To disconnect from the accumulator a weight wire.
2. To remove maple a belt of a drive of the generator and the pump of cooling liquid.
3. To unscrew a bolt of fastening of a pulley to a cranked shaft.
4. By means of a stripper to remove a pulley from a cranked shaft.
5. To remove the bottom casing kardanny chains of system of a gazoraspredeleniye.
6. To remove the tension device kardanny chains of the oil pump.
7. To remove from a shaft of the oil pump an asterisk together with a chain.
8. To unscrew bolts with a nest of Torx of fastening of the oil pump.
9. To remove the oil pump.

Installation of the oil pump

PERFORMANCE ORDER
1. To check a condition and in case of need to replace laying of the oil pump.
2. To establish the oil pump with laying.
3. To screw bolts with a nest of Torx of fastening of the oil pump.
4. To turn several times a pump shaft for an oil zasasyvaniye.
5. To put on an asterisk of the oil pump ("FRONT" inscription on an asterisk should be visible in front of the engine) together with kardanny a pump chain.
6. To tighten a bolt with a nest of Torx of fastening of an asterisk on a pump shaft.
7. To establish the tension device kardanny to chains of the oil pump.
8. To screw with the established new laying the bottom casing kardanny chains of system of a gazoraspredeleniye.
9. To put on a pulley a cranked shaft.
10. To tighten a bolt of fastening of a pulley of a cranked shaft.
11. To put on maple a belt of a drive of the generator and the pump of cooling liquid and to adjust its tension.

Check and oil pump

PERFORMANCE ORDER
1. To remove the oil pump.
2. To unscrew bolts of Torx of fastening of a cover of the oil pump.
3. To uncover the oil pump.
4. With the help щупа and rulers to check gaps between elements of the oil pump.
5. Check a radial gap between gear wheels.
6. Check a radial gap between a rotor and the pump case.
7. Check an axial gap.
8. To take gear wheels of the oil pump and to check their condition.
9. To insert gear wheels into the pump case so that their designations were visible.
10. To establish a cover of the oil pump.
11. To tighten bolts of Torx of fastening of a cover of the oil pump.
12. To establish the oil pump on the block of cylinders of the engine. Other information of rather technical characteristics, adjustment and repair of the engine is in is in subsection 4.1 and subsection 3.1.3.1.