Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
- 3. General data
   + 3.1. Cars with petrol engines
   - 3.2. Cars with diesel engines
      - 3.2.1. Changes in a car design from 1988 to 1993.
         3.2.1.1. Dm3 engine 2,3
         - 3.2.1.2. Dm3 engine 1,8
            3.2.1.2.1. Technical characteristics
            3.2.1.2.2. Head of the block of cylinders
            3.2.1.2.3. Block of cylinders
            3.2.1.2.4. Krivoshipno-shatunny mechanism
            3.2.1.2.5. Gazoraspredeleniye system
            3.2.1.2.6. Greasing system
            3.2.1.2.7. Cooling system
            3.2.1.2.8. Fuel system
            3.2.1.2.9. Tightening moments
            3.2.1.2.10. Engine adjustment
         + 3.2.1.3. Fuel system
         + 3.2.1.4. The repair which is not demanding removal of the engine
         3.2.1.5. Removal and engine installation
         3.2.1.6. Engine dismantling
         3.2.1.7. Check of details
         3.2.1.8. Check of gaps of a cranked shaft and rods
         3.2.1.9. Engine assembly
         3.2.1.10. Greasing system
         3.2.1.11. Cooling system
         3.2.1.12. Coupling
         3.2.1.13. Mechanical five-speed transmission of MT 75 type
         3.2.1.14. Power shaft and back bridge
         3.2.1.15. Steering system
         3.2.1.16. Forward suspension bracket
         3.2.1.17. Brake system
         3.2.1.18. Electric equipment
         3.2.1.19. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






3.2.1.2.9. Tightening moments

GENERAL INFORMATION

Bolts of fastening of a head of the block of cylinders (each time new bolts):
  – 1 stage
20-30 Nanometers
  – 2nd stage
76-92 Nanometers
  – 3rd stage
to wait 2 minutes
  – 4th stage
to tighten on 90 °
Covers of bearings of a cam-shaft
16-22 Nanometers
Covers of radical bearings:
  – 1 stage
20-30 Nanometers
  – 2nd stage
to tighten on 45 °
Covers of rods:
  – 1 stage
20-30 Nanometers
  – 2nd stage
to tighten on 60 °
  – 3rd stage
to tighten on 20 °
Flywheel:
  – 1 stage
15-20 Nanometers
  – 2nd stage
to tighten on 45 °
  – 3rd stage
to tighten on 45 °
Pulley of an intermediate shaft
40-51 Nanometers
Pulley of the fuel pump
20-25 Nanometers
Tension device of a gear belt of a drive of the fuel pump
40-57 Nanometers
Cam-shaft pulley
  – bolt М6
8–10 Nanometers
  – bolt М8
27-33 Nanometers
Tension device of a gear belt of a drive of a cam-shaft
45-55 Nanometers
Intermediate pulley
40-51 Nanometers
Casing of driving belts of system of a gazoraspredeleniye and fuel pump
8–10 Nanometers
Back cover to the block of cylinders
16-21 Nanometers
Forward cover to the block of cylinders
20-28 Nanometers
The oil pump to the block of cylinders
20-25 Nanometers
Basic bearing intermediate валa
8–10 Nanometers
Sealant of an intermediate shaft
20-25 Nanometers
Oil pallet
6–9 Nanometers
Fuel насоc
18-22 Nanometers.
Cover of a head of the block of cylinders
3–4 Nanometers
Glow plugs
25-30 Nanometers
Nozzles to a head of the block of cylinders
60-80 Nanometers
Connections of pipelines of nozzles
15-25 Nanometers
Inlet and final collectors to a head of the block of cylinders
10-14 Nanometers
Bolts of a final collector
20-28 Nanometers