Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
- 3. General data
+ 3.1. Cars with petrol engines
- 3.2. Cars with diesel engines
- 3.2.1. Changes in a car design from 1988 to 1993.
3.2.1.1. Dm3 engine 2,3
+ 3.2.1.2. Dm3 engine 1,8
+ 3.2.1.3. Fuel system
+ 3.2.1.4. The repair which is not demanding removal of the engine
3.2.1.5. Removal and engine installation
3.2.1.6. Engine dismantling
3.2.1.7. Check of details
3.2.1.8. Check of gaps of a cranked shaft and rods
3.2.1.9. Engine assembly
3.2.1.10. Greasing system
3.2.1.11. Cooling system
3.2.1.12. Coupling
3.2.1.13. Mechanical five-speed transmission of MT 75 type
3.2.1.14. Power shaft and back bridge
3.2.1.15. Steering system
3.2.1.16. Forward suspension bracket
3.2.1.17. Brake system
3.2.1.18. Electric equipment
3.2.1.19. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment
|
Cooling system
1–radiator,
2–casing of the fan of a radiator,
3–fan of a radiator,
4–case of the thermostat,
5–thermostat,
6–the pump of cooling liquid,
|
7–broad tank,
8–the sensor of temperature of cooling liquid,
9–thermoswitch of the fan of a radiator. |
THE PUMP OF COOLING LIQUID
Removal
| PERFORMANCE ORDER |
| 1. To disconnect from the accumulator a weight wire. |
| 2. To merge cooling system (see below). |
| 3. To remove the air filter. |
| 4. To remove a gear belt of a drive of a cam-shaft (see subsection 3.2.1.4.2). |
| 5. To remove the bottom casing of a drive of system of a gazoraspredeleniye. |
| 6. To remove a roller of the tension device of a gear belt of a drive of system of a gazoraspredeleniye. |
| 7. To unscrew a hairpin from the case of the pump of cooling liquid. |
| 8. To disconnect the elastic pipeline from the pump of cooling liquid. |
| 9. To remove the pump of cooling liquid. |
|
Installation
Prevention
In case of replacement of the pump of cooling liquid it is recommended to establish also a new gear belt of a drive of system of a gazoraspredeleniye.
| PERFORMANCE ORDER |
| 1. To clear surfaces of a prileganiye of laying in the block of cylinders of the engine and the case of the pump of cooling liquid. |
| 2. To establish new laying of the pump of cooling liquid. |
| 3. To screw the pump of cooling liquid on the block of cylinders, without tightening up to the end fastening bolts. |
| 4. To connect to the pump of cooling liquid the elastic pipeline of system of cooling. To establish a white sign on the pipeline opposite to a sign on a ledge of the case of the pump. |
| 5. To tighten bolts of fastening of the pump of cooling liquid the corresponding moment. |
| 6. To screw up on the corresponding place in the case of the pump of cooling liquid a hairpin, having greased a carving with a small amount of Loctite 242 glue. |
| 7. To establish the bottom casing of a drive of system of a gazoraspredeleniye. |
| 8. To establish a roller and a spring of the tension device of a gear belt of a drive of system of a gazoraspredeleniye. To establish a roller so that its spring was most compressed. |
| 9. To establish a gear belt of a drive of system of a gazoraspredeleniye (see subsection 3.2.1.4.4). |
| 10. To establish the air filter. |
| 11. To connect to the accumulator a weight wire. |
| 12. To fill system of cooling and to remove from it air (see below). |
| 13. To check tightness of connections. |
|
Plums of system of cooling
Prevention
Cooling liquid is recommended to be changed on the cold engine.
| PERFORMANCE ORDER |
| 1. To disconnect from the accumulator a weight wire. |
| 2. Carefully to unscrew a stopper of a broad tank of system of cooling. |
| 3. To put under a radiator capacity for following liquid from cooling system. |
| 4. To unscrew a stopper plum on a radiator. |
|
5. To unscrew a stopper plum on the block of cylinders of the engine, located below the vacuum pump. |
|
Filling of system of cooling and air removal from it
| PERFORMANCE ORDER |
| 1. To screw up both drain stoppers (in a radiator and in the block of cylinders of the engine). |
| 2. To unscrew a bolt of a deaerator of system of the cooling, located in the top elastic pipeline of a radiator. |
| 3. To fill in cooling liquid through an opening in a broad tank while it will not start to follow from under a bolt of a deaerator of system of cooling. |
| 4. To screw up a bolt of a deaerator of system of cooling. |
| 5. To fill in cooling liquid to the maximum level corresponding to the sign "MAX" on the case of a tank. |
| 6. Again to fill in cooling liquid in a broad tank to "MAX" level. |
| 7. To screw up a stopper of a broad tank. |
| 8. To check tightness of connections of system of cooling. |
|
|
|