Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
- 3. General data
   - 3.1. Cars with petrol engines
      3.1.1. Masses and transfer numbers
      3.1.2. Operational liquids
      + 3.1.3. Changes in a car design from 1984 to 1986.
      - 3.1.4. Changes in a car design from 1987 to 1989.
         3.1.4.1. OHC engine
         - 3.1.4.2. Dm3 CVH 1,8 engine
            + 3.1.4.2.1. Technical characteristics
            3.1.4.2.2. Engine adjustment
            3.1.4.2.3. Ignition system
            3.1.4.2.4. Gazoraspredeleniye system
            3.1.4.2.5. Assembly of the CVH 1,8 engine of dm3
         + 3.1.4.3. DOHC engine
         + 3.1.4.4. Service and repair
         + 3.1.4.5. Coupling
         3.1.4.6. Mechanical five-speed transmission of type N
         + 3.1.4.7. Mechanical five-speed transmission of MT 75 type
         3.1.4.8. Automatic transmission
         3.1.4.9. Forward suspension bracket
         + 3.1.4.10. Brake system
         + 3.1.4.11. Electric equipment
         3.1.4.12. General data
      + 3.1.5. Changes in a car design with 1990 till February, 1993.
   + 3.2. Cars with diesel engines
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






3.1.4.2.4. Gazoraspredeleniye system

GENERAL INFORMATION

System of a gazoraspredeleniye of the CVH engine

1–top casing of a drive of system of a gazoraspredeleniye,
2–bottom casing of a drive of system of a gazoraspredeleniye,
3, 4 – laying,
5–maple pulley of a cranked shaft,
6–gear pulley of a cranked shaft,
7–a directing disk of a gear belt,
8–gear belt,
9–tension device of a gear belt,
10-pulley of a cam-shaft,
11-a pulley of the pump of cooling liquid, 12 – a sealing ring of a cam-shaft, 13 – an adjusting plate,
14-cam-shaft

Installation of a gazoraspredeleniye of the CVH engine

1–adjusting signs of a cam-shaft,


2–adjusting signs of a cranked shaft

Head of the block of cylinders of the CVH engine

1–cover of a head of the block of cylinders,

2–head of the block of cylinders,

3–lever of the valve,

4–hydraulic pusher,

5–spring of the valve,

6–laying of a head of the block of cylinders,

7, 8 – directing valves,

9, 10 – saddles of valves,

11-the sensor of temperature of cooling liquid,

12, 13 – the valve

Block of cylinders of the CVH engine

1–block of cylinders,

2–a drain stopper of cooling liquid,

3–caps of oil channels,

4–laying,

5–back cover of the block of cylinders,

6–an oil separator in system of ventilation of karterny gases

Removal of a gear belt

PERFORMANCE ORDER
1. To disconnect from the accumulator a weight wire.
2. To remove maple a belt of a drive of the generator.
3. To disconnect a plait of electric wires of system of ignition, to remove the distributor of a high voltage, a rotor of the distributor and the holder of the distributor of ignition (see fig. System of a gazoraspredeleniye of the CVH engine).
4. To remove a casing of a drive of system of a gazoraspredeleniye.
5. To turn a cranked shaft before sign installation on a cam-shaft pulley opposite to a sign on a head of the block of cylinders (1) (see fig. Installation of a gazoraspredeleniye of the CVH engine).
6. To weaken a bolt of blocking of the tension device of a gear belt. To move a roller to the left and to tighten blocking bolt.
7. To remove a gear belt.

Adjustment of a gazoraspredeleniye and installation of a gear belt

PERFORMANCE ORDER
1. To establish a sign on a cam-shaft pulley opposite to a sign on a head of the block of cylinders (1) (see fig. Installation of a gazoraspredeleniye of the CVH engine).
2. To turn a cranked shaft before installation of a sign of a pulley of a cranked shaft (2) opposite to a sign on a case of the oil pump.
3. To insert a spring of the tension device, the tension device and to block it in situation against the stop to the left.

Prevention

This spring is not established at plant, the gear belt stretches by means of the special adaptation. After weakening of fastening of the tension device it is necessary to establish surely a spring for providing the correct tension of a gear belt.


4. To put on a gear belt, beginning from a pulley of a cranked shaft, in the direction counter-clockwise.
5. To unblock the tension device so that its roller pulled a gear belt.
6. To execute two complete revolutions of a cranked shaft in the direction clockwise and to establish a sign on a cam-shaft pulley opposite to a sign on a head of the block of cylinders.
7. To fix a cranked shaft (having included transfer and having tightened the lever of the hand brake) and to rotate a cam-shaft in the direction counter-clockwise by means of a dinamometrichesky natural a head of 41 mm (through a reduktsionny element 1/2 "–3/4").
Prevention

The head of 41 mm is necessary, as it is impossible to rotate a cam-shaft for a bolt of fastening of its pulley.


8. To hold a cam-shaft with the moment of 23-30 Nanometers and to tighten the tension device of a gear belt the moment of 23-30 Nanometers (at first a bolt on the right side).
9. To check, whether adjusting signs underwent change.
10. To switch off transfer and the hand brake.
11. To turn on two turns a cranked shaft in the direction of its working rotation, then repeatedly to check the provision of adjusting signs.
12. To establish a casing of a drive of system of a gazoraspredeleniye.
13. To establish the distributor of ignition and a wire of a high voltage.
14. To put on and pull a maple belt of a drive of the generator.
15. To connect the accumulator.