Ford Sierra

1982-1993 of release

Repair and car operation


Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
+ 3. General data
- 4. Engines
   - 4.1. Petrol engines
      - 4.1.1. Technical characteristics
         4.1.1.1. Head of the block of cylinders
         4.1.1.2. Block of cylinders of the engine
         4.1.1.3. Krivoshipno-shatunny mechanism
         4.1.1.4. Gazoraspredeleniye system
         4.1.1.5. Greasing system
         4.1.1.6. Cooling system
         4.1.1.7. Fuel system
         4.1.1.8. Ignition system
         4.1.1.9. Tightening moments
      4.1.2. Adjustment of gaps of valves
      + 4.1.3. Ignition system
      + 4.1.4. Fuel system
      + 4.1.5. The repair which is not demanding removal of the engine
      4.1.6. Removal and engine installation
      4.1.7. Engine dismantling
      4.1.8. Identification of cooperating parts
      4.1.9. Engine assembly
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. Gazoraspredeleniye system
      4.1.13. Greasing system
      + 4.1.14. Cooling system
      4.1.15. Suspension bracket of the power unit
      4.1.16. System of production of the fulfilled gases
   + 4.2. Diesel engine
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






4.1.1.9. Tightening moments
GENERAL INFORMATION

Bolts of covers of radical bearings
88-102 Nanometers
Bolts of rods
40-47 Nanometers
Bolt of a pulley of a cranked shaft
55-60 Nanometers
Bolt of a gear wheel of a cam-shaft
45-50 Nanometers
Flywheel bolts
67-70 Nanometers
Bolts of fastening of the oil pump
17-21 Nanometers
Bolts of a cover of the oil pump
9–13 Nanometers
Bolts of the oil pallet (a tightening order – look subsection 4.1.9)
  – 1st stage
1–2 Nanometers
  – 2nd stage
6–8 Nanometers
  – the 3rd stage (after 20 minutes of operation of the engine)
8–10 Nanometers
Stopper oil plum in the oil pallet
21-28 Nanometers
Sensor of pressure of oil
12-15 Nanometers
Bolts of adjustment of a gap of valves about levers of valves
50-55 Nanometers
Bolts of a head of the block of cylinders (a tightening order – see in subsection 4.1.5.4)
  – 1st stage
40-45 Nanometers
  – 2nd stage
50-70 Nanometers;
  – the 3rd stage (later 10-20 mines)
73-83 Nanometers
  – the 4th stage (after 15 minutes of operation of the engine at number of turns of 1000 rpm; at the hot engine)
95-115 Nanometers
Casing of system of a gazoraspredeleniye
13-17 Nanometers
Inlet collector
17-21 Nanometers
Final collector
21-25 Nanometers
Spark plugs
20-28 Nanometers
Thermostat case
17-21 Nanometers
Bolts of a cover of a head of the block of cylinders (a tightening order – see in subsection 4.1.5.4)
  – bolts 1-6 and 9, 10
5–7 Nanometers
  – bolts 7 and 8
2–2,5 Nanometers