Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
+ 3. General data
- 4. Engines
   - 4.1. Petrol engines
      + 4.1.1. Technical characteristics
      4.1.2. Adjustment of gaps of valves
      + 4.1.3. Ignition system
      + 4.1.4. Fuel system
      + 4.1.5. The repair which is not demanding removal of the engine
      4.1.6. Removal and engine installation
      4.1.7. Engine dismantling
      4.1.8. Identification of cooperating parts
      4.1.9. Engine assembly
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. Gazoraspredeleniye system
      4.1.13. Greasing system
      + 4.1.14. Cooling system
      4.1.15. Suspension bracket of the power unit
      4.1.16. System of production of the fulfilled gases
   + 4.2. Diesel engine
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


амаранта масло в Киеве



4.1.7. Engine dismantling

GENERAL INFORMATION

Knot of the block of cylinders

1–oil pallet,
2–laying of the oil pallet,
3–block of cylinders,
4–back consolidation of a cranked shaft,
5–laying of the fuel pump,

6–laying of the pump of cooling liquid,
7–forward cover of the block of cylinders,
8–laying,
9–cover of the radical bearing

PERFORMANCE ORDER
1. To arrange the engine on the corresponding bed.
2. To merge oil from the oil pallet, to unscrew the oil filter and to take the index of level of oil.
3. To remove a leading part and a coupling disk (to designate the direction of its installation).
4. To unscrew spark plugs and to remove the ignition distributor, having designated its situation for simplification of the subsequent installation. To disconnect the vacuum pipeline.
5. To remove a casing of a gear belt and a pulley of the pump of cooling liquid.
6. To uncover heads of the block of cylinders.
7. To remove the generator and maple a belt of a drive of the fan, and a pulley of the pump of cooling liquid.
8. To unscrew bolts of fastening and to remove a pulley from a cranked shaft.
9. To unscrew and take a bolt, a washer and a pulley of an intermediate shaft.
10. To weaken the tension device of a gear belt, to move it, overcoming resistance of a spring and to fix in the situation removed from a belt.
11. To remove a gear belt.
12. To remove pulleys from a cranked shaft (in case of need by means of a stripper 21.028), an intermediate shaft and a cam-shaft.
13. To disconnect from the carburetor топливопровод.
14. To unscrew bolts of fastening of a head of the block of cylinders as it should be the return to their tightening (see fig. An order of a tightening of bolts of a head of the block of cylinders) and to remove it together with inlet and final collectors.
15. To take two bolts from the chamber of removal of cooling liquid (from a head of the block of cylinders) to remove an adjusting ring and to take the thermostat and laying.
16. To remove the oil pump, a pusher and топливопроводы.
17. To unscrew the sensor of pressure of oil and by means of a screw-driver to take its settler.
18. To remove the oil pallet.
19. To remove a forward cover of the block of cylinders.
20. To remove (after unscrewing of two bolts) the basic bearing of an intermediate shaft.
21. By means of a stripper 22.036 to take from an opening in a back part of a cranked shaft the bearing of a shaft of coupling.
22. To establish pistons on a half of height of cylinders for removal possibility (by means of a scraper) a deposit from the top part of cylinders.
23. To incline the engine for plum of the remains of oil from the block of cylinders.
24. To remove the pump of cooling liquid.
25. To remove the oil pump (adaptation 21.012), and also to take its power shaft.
26. To check presence of designations of radical bearings (on covers and the block of cylinders of the engine), and also designations of shatunny bearings (on rods and covers). In case of their absence it is necessary to designate bearings by means of a center punch or an indelible pencil.
27. To unscrew bolts of rods, to remove their covers, to take shatunny loose leaves and to take pistons together with rods from cylinders.
28. To remove a flywheel.
29. To unscrew bolts of covers of radical bearings, to remove covers of radical bearings and to take loose leaves.
30. To take from the block of cylinders a cranked shaft and its back sealant.
31. To take persistent half rings of a cranked shaft from the average radical bearing.