Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
+ 3. General data
- 4. Engines
   - 4.1. Petrol engines
      + 4.1.1. Technical characteristics
      4.1.2. Adjustment of gaps of valves
      + 4.1.3. Ignition system
      + 4.1.4. Fuel system
      + 4.1.5. The repair which is not demanding removal of the engine
      4.1.6. Removal and engine installation
      4.1.7. Engine dismantling
      4.1.8. Identification of cooperating parts
      4.1.9. Engine assembly
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. Gazoraspredeleniye system
      4.1.13. Greasing system
      + 4.1.14. Cooling system
      4.1.15. Suspension bracket of the power unit
      4.1.16. System of production of the fulfilled gases
   + 4.2. Diesel engine
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






4.1.11. Removal and installation of an intermediate shaft

GENERAL INFORMATION

Removal and installation of an intermediate shaft

1–cover,

2–laying,

3–sealing ring,

4–intermediate shaft,

5–adjusting axial plate,

6–bearing plug

Removal

PERFORMANCE ORDER
1. To disconnect a weight wire from the accumulator.
2. To weaken bolts of fastening of the generator and to remove maple a belt of its drive.
3. To remove a casing of a gear belt.
4. To remove a pulley from a cranked shaft and its persistent laying.
5. To establish the piston of the 1st cylinder in VMT, to designate the provision of a rotor of the distributor and to remove the ignition distributor.
6. To unscrew a bolt of fastening of a pulley on intermediate to a shaft.
7. To weaken fastening of the tension device and to remove a gear belt.
8. To remove the fuel pump and a pusher of its drive.
9. To unscrew a cover of an intermediate shaft, an adjusting plate and to remove an intermediate shaft.
10. To take a sealing ring from a cover of an intermediate shaft.

Installation

PERFORMANCE ORDER
1. To establish in a cover a sealing ring of an intermediate shaft.
2. To fix in the block of cylinders an intermediate shaft and an adjusting plate. To check axial люфт an intermediate shaft (in case of need to replace an adjusting plate, selecting respectively its thickness).
3. To oil edges of a sealing ring and to establish it on an intermediate shaft together with a cover with the help the adaptation 21.009 A.
4. To establish a pulley on an intermediate shaft.
5. To insert into an opening in the block of cylinders a pusher of a drive of the fuel pump and to fix the pump.
6. To establish a pulley on intermediate to a shaft so that edges of strengthening of a pulley were directed towards the block of cylinders.
7. To check, whether correspond the provision of a cranked shaft, a cam-shaft and the ignition distributor to position of the piston of the 1st cylinder in VMT. To fix the distributor of ignition and to check correctness of its installation.
8. To establish a gear belt and to adjust its tension.
9. To establish on cranked to a shaft persistent laying, and then to fix a pulley on cranked to a shaft.
10. To establish a casing of a gear belt.
11. To establish maple a belt of a drive of the generator and the fan, to adjust its tension (the deflection should make 10 mm in the middle between pulleys of a cranked shaft and the generator).
12. To establish the ignition distributor, to connect wires of a high voltage and a weight wire to the accumulator.