Ford Sierra

1982-1993 of release

Repair and car operation


Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
+ 3. General data
- 4. Engines
   - 4.1. Petrol engines
      + 4.1.1. Technical characteristics
      4.1.2. Adjustment of gaps of valves
      - 4.1.3. Ignition system
         4.1.3.1. The sensor of impulses with the Hall converter
         4.1.3.2. To distribute ignitions
         4.1.3.3. Switchboard
         4.1.3.4. Remarks on operation
         4.1.3.5. Installation of a corner of an advancing of ignition
         4.1.3.6. Determination of malfunctions
         4.1.3.7. Removal and installation of the distributor of ignition
      + 4.1.4. Fuel system
      + 4.1.5. The repair which is not demanding removal of the engine
      4.1.6. Removal and engine installation
      4.1.7. Engine dismantling
      4.1.8. Identification of cooperating parts
      4.1.9. Engine assembly
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. Gazoraspredeleniye system
      4.1.13. Greasing system
      + 4.1.14. Cooling system
      4.1.15. Suspension bracket of the power unit
      4.1.16. System of production of the fulfilled gases
   + 4.2. Diesel engine
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment






4.1.3.6. Determination of malfunctions
GENERAL INFORMATION

The transistor system of ignition should be checked at well charged accumulator and at temperature 0 °–-40 ° S.Sleduyet to arrive according to instructions given below.

The starter rotates a cranked shaft, however the engine is not started
To check existence of a high voltage on spark plugs
The high voltage is present
To check system of ignition of the engine
The high voltage is absent
To check existence of a high voltage on distributor plugs
The high voltage is present
To check a rotor and a distributor cover, and also wires of a high voltage. To replace the damaged elements
The high voltage is absent
To check existence of a high voltage on distributor plugs
The high voltage is present
To check a rotor and a distributor cover, and also wires of a high voltage. To replace the damaged elements
The high voltage is absent
To check existence of a high voltage on plugs of the coil of ignition
The high voltage is present
To replace a wire of a high voltage between the coil and the ignition distributor
The high voltage is absent
To check all electric connections of system of ignition
Too big power failure or temporary short circuit
To clear or replace sockets of electric wires
It is not revealed damages
To check tension existence on the +VE plug of the coil of ignition (tension of the accumulator)
Tension wrong
To check the ignition switch, a condition of the accumulator and its electric wires
Tension correct
To disconnect two wires of a low voltage from the ignition coil. To connect to the socket a bulb 12 In / 21 W and to include a starter
The bulb blinks in starter operating time
To replace the ignition coil
The bulb does not burn (does not blink)
To disconnect the multicontact socket from the distributor of ignition and to measure resistance between socket contacts
Resistance does not correspond to norm
To replace the ignition distributor
Resistance normal
To connect the multicontact socket to the distributor of ignition to connect the new switchboard of ignition. To include a starter. The bulb connected to plugs of a low voltage of the coil of ignition, should blink
If the bulb blinks, to connect wires to the coil of ignition and to check, whether the engine is correctly started