Repair and Ford Sierra car operation - 10.2. Forward brakes//Ford Siyerra 1982-1993 / informatic74.ru

Ford Sierra

1982-1993 of release

Repair and car operation



Ford Siyerra
+ 1.2. Car identification
+ 2. Maintenance
+ 3. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
- 10. Brake system
   10.1. Technical characteristics
   - 10.2. Forward brakes
      10.2.1. Replacement of brake shoes
      10.2.2. Support replacement
      10.2.3. Replacement of a brake disk
      10.2.4. Support repair
   + 10.3. Back brakes
   10.4. Removal and installation of the main brake cylinder
   10.5. Air removal from brake system
   10.6. Adjustment of the hand brake
+ 11. Body
+ 12. Electric equipment


×èòàåì òóò: https://myavto24.ru | Ïîñëåñòðîèòåëüíàÿ óáîðêà: https://skifcleaning.com | Ýòî íàäî çíàòü: https://myworldland.ru | Åñëè ðåáåíîê: https://gelschool.ru | Èíòåðåñíûå íîâîñòè: https://marta-ko.ru | ×èòàåì ïðî íîâîå: https://ododru.ru | Èíòåðåñíîå íà æåíñêîì ñàéòå: https://glamorlady.ru | Âñå î çäîðîâüå: https://furycoins.ru | Çäåñü: https://lumberwood.ru | Óâëåêàòåëüíàÿ ðûáàëêà íà îêóíÿ. | Àâòî íîâîñòè Auto-M: https://auto-magazine.net | ×èòàåì î íîâîì: https://lidomed.ru | ×èòàåì íà ñàéòå: https://medprav.ru | Íîâîñòíîé ðåñóðñ: https://pridemed.ru | Íîâîñòíîé ðåñóðñ: https://evroinstroy.ru




10.2. Forward brakes

10.2.1. Replacement of brake shoes

GENERAL INFORMATION

Forward brake

And – cars with engines 1,3 and 1,6 of dm3,

In – cars with the engine 2,0 of dm3,

1–arm of a support,

2–support,

3–brake shoes,

4–piston,

5–brake disk


CARS WITH DM3 ENGINES 1,3 AND 1,6
Prevention

Simultaneous replacement of all brake shoes of forward brakes if at least one of them wears out till the minimum thickness is recommended.


Replacement

PERFORMANCE ORDER
1. To weaken nuts of fastening of forward wheels.
2. To lift and fix in front of the car, to remove forward wheels.
3. To unscrew in the top part of a support a bolt of fastening of a support of a brake to the holder, holding with a flat key the top directing finger.
4. To take a bolt of fastening of a support of a brake to the holder.

Prevention

In cars with engines 2,0 of dm3 it is necessary to unscrew two bolts.


5. To reject back a support concerning the holder and to take brake shoes.
6. Carefully to press the piston in a support by means of the corresponding wooden core, being careful not to damage an elastic casing of the piston. In case of need it is possible to remove previously a little brake liquid from a tank.
7. To check a condition of a brake disk and an elastic casing of the piston.
8. To establish on the corresponding places brake shoes with an anti-vibrating level, to turn a support in the direction of his holder.
9. To tighten a bolt of fastening of a support the moment of 32 Nanometers.
10. In the same way to replace brake shoes in the second forward brake.
11. To establish wheels, to lower the car and to tighten nuts of fastening of wheels.
12. Several times strongly to press a pedal of a brake to bring into contact brake shoes with a brake disk.

13. In case of need to add amount of brake liquid in a tank.


CARS WITH DM3 ENGINES 2,0

Replacement

PERFORMANCE ORDER
1. To weaken nuts of fastening of forward wheels.
2. To lift and fix in front of the car, to remove forward wheels.
3. Carefully to pick up a screw-driver and to take a bracket of fastening of a support of a brake.
4. By means of a key for internal shestigrannik of 7 mm to unscrew two directing fingers of a support.
5. To disconnect sockets of wires of the sensor of wear of brake shoes.
6. To disconnect a support from the holder and to suspend it to a body by means of a wire (without unscrewing of connection of brake hoses).
7. To take from a support an internal brake shoe and an external brake shoe from directing blocks.
8. Carefully to press the piston in a support by means of the corresponding wooden core, being careful not to damage an elastic casing of the piston. In case of need it is possible to remove previously a little brake liquid from a tank.
9. To check a condition of a brake disk and an elastic casing of the piston.
10. To establish an internal brake shoe in a support and to press into the piston a spring of an internal block. To establish an external brake shoe in directing a support.
11. To establish a support in directing and to screw up two directing fingers of a support, tightening them the moment of 20 Nanometers.
12. To establish on the corresponding place a bracket of fastening of a support of a brake.
13. In the same way to replace brake shoes in the second forward brake.
14. To establish wheels, to lower the car and to tighten nuts of fastening of wheels.
15. Several times strongly to press a pedal of a brake to bring into contact brake shoes with a brake disk.

16. In case of need to add amount of brake liquid in a tank.